Hot Products

abrasion testing machine
Taber Wear and Abrasion Testers M009B

To determine the wear resistance(including mass loss, thickness loss, and transmittance etc.) of all kinds of structures including textiles, paper, glass, metals, paints, plated surfaces, coated materials, leather and rubber.

EN 71 KE Tester
Kinetic Energy Tester T011

T011 Kinetic Energy Tester is used to test the maximum energy produced from projectile toy shoot bullets or launched bows, so as to evaluate ejection articles will cause injury for children or not.

Dynamic Strength Tester
Toy Dynamic Strength (2m/s) Tester T012

T012 Dynamic Strength & 2m/s Tester is used test dynamic strength for wheeled ride-on toys. Simulate children wheeled ride-on toys vertically crush the inelastic step 50 x 50 mm at the stable speed of 2m/s±0.2/s, and then check the damage degree. This device can be used for children ride-on toys, such as children tricycle, toy bikes, scooters, etc.

Sharp Point Tester
Sharp Point Tester T004

Sharp point tester is to determine whether accessible sharp points on child-related products are likely to cause injury. If the accessible sharp point penetrates a specified depth into the small rectangular opening of the tester, the LED is illuminated to indicate that the point is unacceptably sharp.

Mouth Toy Endure Tester
Mouth Actuated Toy Tester T005

Used to test the safety of the Mouth-Actuated Toys, such as whistles with a ball, the sounders with a reed and other toys. Load the mouth-actuated projectile toy with the intended projectile and apply a pressure of 13,8 kPa ± 5 % in the direction of the mouthpiece for 5 s. Carry out the test 10 times in total.

Toys Accessibility Probe
Accessibility Probe T006

Accessibility Probe is used to assess the surface or components (points and surface of toys) of toys is likely to be touched and lead to hazardous. If the probe contacts the part or component, the part or component is considered to be accessible. Therefore, to do related tests based on standards to decrease hazards for children. This tools are including 2 parts: Probe A and Probe B. An accessible point for a toy or article intended for children 3 years of age or less is one that can be contacted by any portion forward of the collar of the accessibility probe designated as Probe A . An accessible point for a toy or article intended for children over 3 years of age is one that can be contacted by any portion forward of the collar of the accessibility probe designated as Probe B . An accessible point for a toy or article intended for children of ages spanning both age groups is one that can be contacted by any portion forward of the collar of either Probe A or B.

color matching cabinets
Color Matching Cabinets D008

Color light box/Color matching cabinet, to do color matching or assessment for all industries and applications where there is a need to maintain color consistency and quality. Such as, Dyeing, Packaging, Printing, Footwear, Inks and Textile, Automotive, Ceramics, Cosmetics, Foodstuffs, Furniture, knitwear, Leather, Ophthalmic,etc. D65, TL84, CWF, F, UV, U30 light sources are available for this light box.

EN 71 toy tester
Sharp Edge Tester T001

T001 Sharp edge tester is used to determine whether the accessible edges on child-related products are likely to cause potential risk of injury after normal use and reasonable abuse. Those child-related products include metal or glass edges on toys and other articles intended for use by children under 8 years of age.

ISO 17707 Whole Sole Flexing Machine
Whole Sole Flexing Machine H018

H018 Whole Sole Flexing Machine, to measure the material's resistance to incision elongation(cut growth) during repeated flexing, especially for outsoles of protective footwear, including soles. The machine has three vertical or horizontal stations available for customized and is easy to operate. Loading, unloading and measurements are also much easier to carry out with the workstations provided. The sample flexes at speed of 140 times per minute, and the exact number is recorded in a counter that has been preset to the required number of flexing. A fixture can be used to position the steel chisel, which can be used to support the sample after the initial chipping. All mobile parts that need access are fully protected with a fully interlocked security cover to ensure that the machine complies with the latest security regulations. A manual device can be used to measure the hardness of the outer bottom and check whether the outer bottom must be twisted in accordance with EN ISO 20344. UTS also provide a version of this machine for testing at low temperatures allowing tests to be conducted down to -20°C.

Water Resistance Tester
Shoe Water Resistance Tester H009

To determine the waterproofness property for finished shoes. Within the specified depth of water, whole shoe will be mechanically brushed by rotary wet brush, so as to measure the water penetration property for finished shoe.

NBS Abrader - Abrasion Tester
NBS Rubber Abrasion Tester H014

To determine the abrasion resistance property for rubber or other compounds, sole and heel materials which are not less than 2.54mm in thickness. This machine has memory function so that users can set the number of tests by themselves. The current records will be kept not to change even if power failure or stop occurs. It also can be connected to a cleaner for easy cleaning.

astm d1424  Elemendorf Tear Tester
Digital Elemendorf Tear Tester M006B

To determine the tearing resistance strength (Elmendorf method) for various textiles. Also available for thick paper, plastic cloth and electrical insulating tapes. Three interchangeable pendulums ranging from 16,000 to 128,000 Millinewtons (mN) can be selected separately for multiple test method compliance.

Latest news

  • National Day Holiday Notice
    National Day Holiday Notice 2024-09-30

    The National Day is coming soon. According to the State Council's regulations on statutory holidays and the company's actual situation, the company will be on holiday from October 1 to 7 and will work...

  • UTSTESTER Will Show on 28th Textile Asia Internati...
    UTSTESTER Will Show on 28th Textile Asia Internati... 2024/07/12

    Exhibition Background The Textile Asia Exhibition in Pakistan is indeed held in multiple major cities, including Karachi, Faisalabad, and Lahore. These cities are significant hubs for Pakistan's texti...

  • UTSTESTER Team Activity on May - Pick bayberry
    UTSTESTER Team Activity on May - Pick bayberry 2024/05/28

    It is the bayberry season again. In order to fully relax the team's psychology and combine work and rest after work, UTSTESTER's International Business Department organized an outdoor team-building ac...

Universal Strength Tester

Universal Strength Tester is a versatile tester that tests the strength, flexibility and durability of rubber, plastic, fabric, paper, packaging and more.

    A total of

    1

    page

Copyright © UTS International Co., Ltd

Contact Us