Hot Products

abrasion testing machine
Taber Wear and Abrasion Testers M009B

To determine the wear resistance(including mass loss, thickness loss, and transmittance etc.) of all kinds of structures including textiles, paper, glass, metals, paints, plated surfaces, coated materials, leather and rubber.

EN 71 KE Tester
Kinetic Energy Tester T011

T011 Kinetic Energy Tester is used to test the maximum energy produced from projectile toy shoot bullets or launched bows, so as to evaluate ejection articles will cause injury for children or not.

Dynamic Strength Tester
Toy Dynamic Strength (2m/s) Tester T012

T012 Dynamic Strength & 2m/s Tester is used test dynamic strength for wheeled ride-on toys. Simulate children wheeled ride-on toys vertically crush the inelastic step 50 x 50 mm at the stable speed of 2m/s±0.2/s, and then check the damage degree. This device can be used for children ride-on toys, such as children tricycle, toy bikes, scooters, etc.

Sharp Point Tester
Sharp Point Tester T004

Sharp point tester is to determine whether accessible sharp points on child-related products are likely to cause injury. If the accessible sharp point penetrates a specified depth into the small rectangular opening of the tester, the LED is illuminated to indicate that the point is unacceptably sharp.

Mouth Toy Endure Tester
Mouth Actuated Toy Tester T005

Used to test the safety of the Mouth-Actuated Toys, such as whistles with a ball, the sounders with a reed and other toys. Load the mouth-actuated projectile toy with the intended projectile and apply a pressure of 13,8 kPa ± 5 % in the direction of the mouthpiece for 5 s. Carry out the test 10 times in total.

Toys Accessibility Probe
Accessibility Probe T006

Accessibility Probe is used to assess the surface or components (points and surface of toys) of toys is likely to be touched and lead to hazardous. If the probe contacts the part or component, the part or component is considered to be accessible. Therefore, to do related tests based on standards to decrease hazards for children. This tools are including 2 parts: Probe A and Probe B. An accessible point for a toy or article intended for children 3 years of age or less is one that can be contacted by any portion forward of the collar of the accessibility probe designated as Probe A . An accessible point for a toy or article intended for children over 3 years of age is one that can be contacted by any portion forward of the collar of the accessibility probe designated as Probe B . An accessible point for a toy or article intended for children of ages spanning both age groups is one that can be contacted by any portion forward of the collar of either Probe A or B.

color matching cabinets
Color Matching Cabinets D008

Color light box/Color matching cabinet, to do color matching or assessment for all industries and applications where there is a need to maintain color consistency and quality. Such as, Dyeing, Packaging, Printing, Footwear, Inks and Textile, Automotive, Ceramics, Cosmetics, Foodstuffs, Furniture, knitwear, Leather, Ophthalmic,etc. D65, TL84, CWF, F, UV, U30 light sources are available for this light box.

EN 71 toy tester
Sharp Edge Tester T001

T001 Sharp edge tester is used to determine whether the accessible edges on child-related products are likely to cause potential risk of injury after normal use and reasonable abuse. Those child-related products include metal or glass edges on toys and other articles intended for use by children under 8 years of age.

ISO 17707 Whole Sole Flexing Machine
Whole Sole Flexing Machine H018

H018 Whole Sole Flexing Machine, to measure the material's resistance to incision elongation(cut growth) during repeated flexing, especially for outsoles of protective footwear, including soles. The machine has three vertical or horizontal stations available for customized and is easy to operate. Loading, unloading and measurements are also much easier to carry out with the workstations provided. The sample flexes at speed of 140 times per minute, and the exact number is recorded in a counter that has been preset to the required number of flexing. A fixture can be used to position the steel chisel, which can be used to support the sample after the initial chipping. All mobile parts that need access are fully protected with a fully interlocked security cover to ensure that the machine complies with the latest security regulations. A manual device can be used to measure the hardness of the outer bottom and check whether the outer bottom must be twisted in accordance with EN ISO 20344. UTS also provide a version of this machine for testing at low temperatures allowing tests to be conducted down to -20°C.

Water Resistance Tester
Shoe Water Resistance Tester H009

To determine the waterproofness property for finished shoes. Within the specified depth of water, whole shoe will be mechanically brushed by rotary wet brush, so as to measure the water penetration property for finished shoe.

NBS Abrader - Abrasion Tester
NBS Rubber Abrasion Tester H014

To determine the abrasion resistance property for rubber or other compounds, sole and heel materials which are not less than 2.54mm in thickness. This machine has memory function so that users can set the number of tests by themselves. The current records will be kept not to change even if power failure or stop occurs. It also can be connected to a cleaner for easy cleaning.

astm d1424  Elemendorf Tear Tester
Digital Elemendorf Tear Tester M006B

To determine the tearing resistance strength (Elmendorf method) for various textiles. Also available for thick paper, plastic cloth and electrical insulating tapes. Three interchangeable pendulums ranging from 16,000 to 128,000 Millinewtons (mN) can be selected separately for multiple test method compliance.

Latest news

  • UTSTESTER Will Show on 28th Textile Asia Internati...
    UTSTESTER Will Show on 28th Textile Asia Internati... 2024/07/12

    Exhibition Background The Textile Asia Exhibition in Pakistan is indeed held in multiple major cities, including Karachi, Faisalabad, and Lahore. These cities are significant hubs for Pakistan's texti...

  • UTSTESTER Team Activity on May - Pick bayberry
    UTSTESTER Team Activity on May - Pick bayberry 2024/05/28

    It is the bayberry season again. In order to fully relax the team's psychology and combine work and rest after work, UTSTESTER's International Business Department organized an outdoor team-building ac...

  • UTSTESTER Attended Sales Elite Training Activities...
    UTSTESTER Attended Sales Elite Training Activities... 2023-08-23

    In order to further build a guidance marketing team, improve the ability level of sales elites, and consolidate the grassroots battle fortress, UTSTESTER actively participated in the "Foreign Trade Ma...

Environmental Testing Equipment

UTS environmental test solutions are carried out via programmable temperature and humidity chamber, therm shock tester, salt spray tester, walk in constant temperature and humidity chamber, etc.

  • UTS-BW Water Bath(Support to supply with holders)
    UTS-BW Water Bath(Support to supply with holders)
    Suitable for direct heating and auxiliary heating of biological, chemical, physical, plant, chemical and other experimental samples. Routine laboratory temperature control, Escherichia coli detection, sample thawing, bacterial detection, incubation microbial experiments, cell culture, food testing pretreatment, etc.
    Read More
  • Sheet ice maker
    Flake Ice Maker UTS-FIM
    Various types of experiments, hospitals, schools, laboratories,medical, chemical applications, supermarkets, hotels and other seafood products stores etc.
    Read More
  • Cube lce equipment
    Cube lce Machine UTS-CIM
    (1) Cube ice, large contact area, adjustable ice thickness. (2) Stainless steel and ABS engineering plastic shell, beautiful shape, strong, practical. (3) Nickel-plated copper ice plate, flowing vertical ice making, high ice making efficiency, energy saving. (4) "Inteligent core" control system, automatic ice making, automatic ice falling, ice full (5) detection. (6) One-button cleaning function, convenient daily maintenance. (7) LED screen, clear operation, accurate understanding of the machine's working (8) conditions. (9) The tank, sink, and water distribution pipe all meet the food grade standards, safe and (10) hygienic. (11) Built-in refrigerator. (12) The three basic parts(computer board, fan, condenser) are guaranteed for five years
    Read More
  • Steam Water Distiller
    Stainless Steel Steam Water Distiller UTS-20LH
    This product is suitable for medical and health, chemical and scientific research units. The laboratory produces distilled water.
    Read More
  • Automatic Penetrometer
    Automatic Penetrometer UTS-2801H
    The fabric cooling performance tester is a judgment about coldness and warmth formed in the human brain by the temperature stimulation of the fabric after the fabric comes into contact with the human skin. When the fabric comes into contact with the skin, due to the temperature difference, there will be a difference between the fabric and the skin. Heat exchange causes the temperature of the skin to increase or decrease; the form of heat exchange between the fabric and the skin is mainly heat conduction, and the influence of thermal radiation and natural convection inside the fabric is very small and can be ignored; under normal circumstances (except when the ambient temperature is higher than (excluding skin temperature), the skin temperature is higher than the ambient temperature, so the skin temperature often drops after the fabric comes into contact with the skin. Used to test the coolness of pajamas, bedding, fabrics, and underwear.
    Read More
  • humidity environmental test chambers
    Programmable Climatic Test Chamber E001N-408L
    Constant temperature and humidity test chamber can simulate a variety of environmental conditions, can help a variety of products and raw materials to detect heat, humidity, dry, low temperature and other performance, based on new energy, electronics, chemicals, automobiles, ships and other large industries and applicable to printing, electronics, metals and other industries.
    Read More
  • climate chamber price
    Constant Temperature Humidity Chamber E001N-225L
    Constant temperature and humidity test chamber, also known as constant temperature and humidity test machine, constant temperature and humidity test chamber, programmable hot and humid alternating test chamber, constant temperature machine or constant temperature and humidity chamber, used to test the performance of materials in a variety of environments and test a variety of materials heat resistance, cold resistance, dry resistance, moisture resistance performance. Suitable for electronics, electrical appliances, cell phones, communications, instruments, vehicles, plastic products, metal, food, chemical, building materials, medical, aerospace and other products for testing quality.
    Read More
  • humidity chamber price
    Temperature Humidity Test Chamber E001N-150L
    Temperature humidity test chamber is to determine resistance to hot, cold, dry and moisture property for various material. Applicable for products quality management of electronic, electrical appliances, food, vehicles, metals, chemicals, building materials, etc.
    Read More
  • climatic test chamber
    Environmental Test Chamber E001N-80L
    E001N Programmable Temperature and Humidity Chamber  Application Constant temperature and humidity chamber is used to determine resistance to hot, cold, dry and moisture property for various material. UTS temperature and humidity chamber is applicable for products quality management of electronic, electrical appliances, food, vehicles, metals, chemicals, building materials, etc. Standards GB/T2423.2-89 High-temperature test method Bb GB2423.1-89 Test A: Low-temperature test method 6 IEC60068-2-1 Low temperature test method Ab GJB150.4-1986 Low temperature test EIA-364-59 Low temperature test IEC60068-2-38 Temperature loops IEC60068-2-78 Constant humidity and heat MIL-STD-202G-103B Humidity test IEC60068-2-30 Humid heat temperature loop EIA-364-31C Humidity resistance GB/T2423.3 Test method for constant humidity and heat GJB150.4-86 Military equipment environmental test method low temperature test GJB150.3-86 Military equipment environmental test method high temperature test GB/T2423.34-2005 Temperature and humidity combined cycle test method Features 1. With USB download function, with RS232 interface, curved software, no need for recorder 2. With vacuum glass observation window, more effective direct observation function 3. Refrigerant servo valve flow calculation control. Energy saving 30%, with a dormant function of the resident flow time, energy saving 50% or more 4. Anti-electromagnetic interference controller with SGS certification; with more than 32 numbers of soft program matching, with multiple development and software upgrade function 5. Defrost cycle (800 defrost cycles once, each defrost guaranteed within 2 hours, integrated test to achieve 25% energy saving) Optional Models Model E001N-80L E001N-150L E001N-225L E001N-408L E001N-800L E001N-1000L Inner box volume 80L 150L 225L 408L 800L 1000L Test chamber size  (W x H x D)cm 40×50×40 50×50×60 60 x 75 x 50 80 x 850 x 60 100 x 100 x 80 100×100×100 External size (D*W*H) (cm) 133*75*172 149* 70*155 149*800*168 159*100*185 179*120*197 199*120*197 Weight(kg) 180 210 260 330 450 500 Power supply 1 Phase, AC 220V 50/60Hz 3 Phase, AC, 380V, 50/60HZ Key Specifications 1. Temperature The temperature range -20 ℃ ~ + 150 ℃ / -40℃ ~ + 150 ℃ / -70℃ ~ + 150 ℃ Temperature deviation ≦ ± 2.0 ℃ Temperature fluctuations ± 0.5 ℃ Temperature evenness ≦ 2.0 ℃ cooling rate Heating rate: - 20 ℃ to + 100 ℃ about 35 min (At no-load state, environmental temperature + 25 ℃) Cooling rate: from + 20 ℃ to - 20 ℃ about 45 min  (At no-load state, environmental temperature + 25 ℃) 2. Humidity Humidity range 20%R.H~98%R.H Humidity deviation ±3.0%RH(>75%RH) ±5.0%RH(≤75%RH) Humidity uniformity ±3.0%RH (No load) Humidity fluctuation ±2.0%RH The temperature and humidity performance test is based on the relevant regulations of iec 60068-3 standard.The sensor is placed at the outlet of the unit. Chamber Structure Consist The test box adopts the whole structure form, that is, the test box consists of three parts: heat preservation box body, independent refrigeration unit and electric control cabinet Composition. Cabinet size Inner box size: W 1000 x H 1000 x D 800 mm Outer box size: W 1200 x H 2035 x D 1815mm (excluding machine stand) Heat preservation box External wall material: high quality carbon steel plate with electrostatic color spray treatment on the surface; Inner wall material :SUS304# fog-faced stainless steel plate; Insulation material: hard polyurethane foam insulation layer + glass fiber. Chamber door Single door, left open, add heating wire to the door frame to prevent condensation at the door frame at low temperature.  observation window W 460 x H 560mm observation window is installed on the door of the box. Multi-layer hollow electrothermal coated glass can effectively keep warm and prevent condensation. Lighting device LED lighting device, installed in Windows Heater High quality nickel-chrome wire electric heater, contactless control mode (SSR). Humidifier Water basin heating and humidifying method; Stainless steel armor heater; Heater control mode: contactless control mode (SSR); Water level control device, heater dry - burning device. The condensate outlet hole equipped with the studio condensate and the unit condensate drain hole. Electrical outlet & cord hole One for each side of left and right chamber, diameter 50mm, equipped with rubber isolation plug and rubber cover. Sample frame Two layers of stainless steel sample frame with adjustable height and carrying weight of 30kg/ layer. Moving castor Including moving castor Power distribution control cabinet. General power circuit breaker and overtemperature protector Complement water system Water pump provide automatic water supply Demonstration Photos Materials To Be Tested Export Shipment Package Related Products        E002A Salt Spray chamber    E002C Composite Salt Wet & Dry Chamber    E002W-8m3 Walk In Salt Spray Tester    M0025BN UV Accelerated Chamber
    Read More
  • salt spray machine price
    Walk In Programmable Salt Spray Tester E002W-8m3
    To do surface processing for various materials, including paints, electroplate, inorganic and anti-rust oil, and after anticorrosion treatment, test the corrosion resistance of their products. Widely used in the aerospace industry, automobile electronics, electronic electrician, mobile phone digital, plastic products, metal materials industries.
    Read More
  • Corrosion tester
    Composite Salt Wet and Dry Test Chamber E002C
    To do surface processing for various materials, including paints, electroplate, inorganic and anti-rust oil, and after anticorrosion treatment, test the corrosion resistance of their products. Widely used in the aerospace industry, automobile electronics, electronic electrician, mobile phone digital, plastic products, metal materials industries.
    Read More
  • salt spray test
    Programmable Salt Spray Tester E002B
    To do surface processing for various materials, including paints, electroplate, inorganic and anti-rust oil, and after anticorrosion treatment, test the corrosion resistance of their products. Widely used in the aerospace industry, automobile electronics, electronic electrician, mobile phone digital, plastic products, metal materials industries.
    Read More
  • 1

    2 3
  • >> A total of

    3

    page

Copyright © UTS International Co., Ltd

Contact Us