(1)size:

1.The left and right foot sizes are the same;

2. The actual size (length) of the shoes is the same, and the size of the lining and middle and bottom plates is the same.

(2) gelatinization:

1. The finished shoes shall not have a length of more than 2mm, a depth of more than 1.5mm, and a gelatinous area only;

2. The connecting surface of the large bottom and the upper surface is firmly bonded, with no cracks or gaps;

3. Tension test: 2.5kg/m2 or above.

(3)Damage:

1. Whether the finished shoe toe, the outer side of the middle upper and the front eye protection display surface are damaged;

2. The inner side of the middle side, etc., without the display surface, shall not be damaged with an area of more than 2 square millimeters;

3. The back collar and tongue should not be damaged;

4. There should be no damage to the needle car, and no damage to the tongue tag;

5. The large bottom is damaged and short of materials, with a length of more than 1mm and a width of 1.5mm;

6. The shoelaces are defective;

(4) firm:

1. The tongue of the shoes must be firmly fixed, and shall not fall off;

2. The ribbon shall be firmly fixed and shall not fall off;

3. Drop molding, trademarks and letters shall not fall off;

4. Be eager and firm without shedding;

5. The size of transfer printing or cloth shall not fall off.

6. The parts and wires shall be firm and shall not fall off;

7.The metal fastener is broken and deformed, loose, without bottom buckle and unqualified for paint dropping;

8. The dripping plastic buckle is not strong, easy to break and unqualified;

9. The connection of large bottom marks is not strong and unqualified;

10. The sole combination is not strong enough to take off the layer unqualified.

(5) color difference:

1. The only color difference is for the weighing part.

2. The left and right feet of the large bottom cannot have color difference.

3. No serious color difference is allowed in accessories, such as trademark, ribbon, drop molding, electric rust, high frequency and printing.

(6) car lines:

1. Any parts, needle car broken unqualified, no bottom line unqualified;

2. The needle car failed to drop the needle;

3. Double needle wire connection, heavy needle, serial line, seriously uneven line spacing, not smooth and unqualified;

4. The stress position, the bottom line of main components, generally too loose, surface line emerging unqualified;

5. The edge spacing and needle spacing are seriously uneven, and the line is not smooth, which seriously affects the appearance and is unqualified.

6. The color of the left and right foot of the car line is wrong, and the color of single needle and double needle line is not qualified.

(7)height:

1. The height of the shoe head shall not exceed 1.5mm, the height of the heel shall not exceed 2mm, and the middle waist shall not be qualified if it exceeds 3mm.

2. The shoes are placed on the plane with large and low unevenness. The shoes are left and right, and the swing warping degree exceeds 2mm.

(8) length:

1. The front side length exceeds 2mm,

2. The length error of tongue exposure exceeds 3mm, which is unqualified.

3.Outsole length of more than 3mm is unqualified;

4. The two ends of shoelaces over 2cm long are unqualified.

(9)slanting:

1. The toe slanting over 1.5mm is unqualified;

2. The heel deflection exceeds 2mm, which is unqualified;

3. The magic buckle belt at the toe of the shoe is not qualified for the slanting 3mm.

(10) sizes:

1. The size of the front (inside head) of the toe is more than 2mm long and 2mm wide.

2. The corresponding position of the left and right feet is obvious and unqualified;

3. After the back collar sponge bag, the collar inside the cloth exposed, obvious size, unqualified.

(11) wrinkles:

1. Wrinkles on the inner head of the shoe body affect the appearance and are unqualified.

2. Large and low bottom sticking, and the corrugated and rolled edge of the side wall affects the appearance, which is unqualified;

3. The upper and bottom of the shoes are not qualified for the following corners and wrinkles;

4. Wrinkles in the inside, unqualified.

(12) needle holes:

1. The outer head, the inner head and the outer side of the middle upper part shall not have needle holes.

2. One needle hole is allowed in the heel and the inside, not more than two holes in each place.

(13) materials:

1. Same pair of shoes, different materials of corresponding parts, unqualified;

2. The color of materials in corresponding parts is different and unqualified;

3. The color, thickness, pattern, villi and decoration of the materials are different and unqualified;

4. Materials with different cutting directions are not qualified;

5. Material crack surface, crack tip, coating peeling, decoloring, discoloring, unqualified;

Shoes need strict testing to ensure our comfortable travel.UTS international co., LTD.Is a company that provides shoe testing equipment. Welcome to contact us.

Email: hello@utstesters.com

Direct: + 86 152 6060 5085

Tel: +86-596-7686689

Web: www.utstesters.com